Step by step guide on how to reprogram an automotive key/door remote for GM Ford and Honda
Yep, you need a tech 2 tool which is like 20 some hundred dollars to program the remote, but it's quick and they should do it for free. Oh and today i went to the dealer to get some keys cut for my aura and i get out of my car and lock it and the one right beside me locks as well. There's like a billion frequencies and i had the same one as the car beside me sooooo when i left i started it. I ordered this Key Fob for my 2008 Mazda 6, a few days later I received the unit and went to a local key shop here in Tucson and had the key cut and the fob programmed for my car. The unit worked perfectly. The local Mazda car dealer wanted to charge me $180.00 for the fob/key unit plus cutting the key and the programming.
Press the vehicle information button until PRESS TO RE- LEARN REMOTE KEY displays. Press the set/reset button until REMOTE KEY LEARNING ACTIVE is displayed.
Difficulty Scale: 1 of 10
Step 1 - GM PASS LOCK RELEARN
- Ignition switch to 'run' position, try to start and let key return to 'run' position
- Approx ten minutes security light will go off
- Turn key 'off' and wait 5 seconds
- Repeat 2 more times for a total of 3 relearns.
- Turn key off, then start it
Step 2 - FORD KEY PADS
- Enter permanent factory code
- Press the 1/2 button within 5 seconds to enter programming mode
- Within 5 seconds enter new code, doors will lock, unlock to verify code, this erases previous codes. Remotes will also need to be programmed.
Step 3 - FORD KEY PADS/REMOTES
Saturn Aura Key Fob Programming
- Insert key, turn ignition off-to-on eight times in succession, ending with key in on position doors will lock, unlock to verify in programming mode
- Press any button on new remote, doors will lock, unlock to verify
- Do the previous step with the second remote, doors will lock unlock to verify.
- Turn ignition switch off. Doors will again lock, unlock to verify.
Step 4 - BLAZER T-CASE SELF DIAGNOSTIC
- Turn ignition switch 'ON' for at least 6 seconds.
- Locate DLC (diagnostic connector) near right side of steering column.
- Install jumper wire from pin #13 (orange wire, labels are small but they are on connector, use flashlight) to ground.
- Turn the key on, engine off. Observe shift select buttons. If they all blink once at the same time there are no trouble codes.
- Otherwise the light will blink (codes are 1-4 flashes) with a 3 second delay between codes if there are more than 1.
- Run the codes if any are present repair as needed.
Step 5 - HONDA SLIDING DOOR RE-HOME
- Erase the sliding door trouble codes by removing the # 13 (7.5) fuse from the passenger's under-dash fuse box for 10 seconds.
- Then put the fuse back in.
- Turn off the main door switch; make sure that the ignition switch is off.
- Manually open the sliding door and make sure it's fully open.
- Turn the ignition switch on, then turn on the door switch.
- Push and hold the CLOSE side of the dashboard door switch for that door until the door is fully closed.
- Try the door operation with the dashboard door switch, the remote and the door handles.
Helpful Information
A remote can perform many functions such as lock and unlock car doors, start the engine, roll up windows and much more. When a key fob is lost or becomes out of sync with the car receiver module, reprogramming is necessary.
Common Problems
- Key fob remote battery goes dead and needs replacement
- Moister damage
One of the more distinct midsize sedans, the Saturn Aura is available in two trim levels according to Edmunds.com. Both trims have V6 engines and sporty features. OEM (Original Equipment Manufacturer) transponder keys and keyless entry car remotes are best seller for the Saturn Aura. Have questions? Our industry-leading customer service staff is here to help. Call (877) 445-3953 Monday to Friday between 8:30AM-5:00PM Eastern Standard Time (EST).
Program Saturn Aura Keyless Fob
Make- Model